User Tools

Site Tools

Translations of this page:

en:duet_reprap_300zl

kraegar's 300ZL config - https://www.dropbox.com/sh/ngmhj4oif2dm8yg/AAC218nV-xNu42qalPdI8IHXa?dl=0

Below is Kraegars config.g , merged into the format exported by https://configurator.reprapfirmware.org/

By starting with this layout it should make it much simpler to compare your file against configurator files.

; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Mon Oct 22 2018 17:23:06 GMT+0100 (British Summer Time)
; based on Tony Akens config.g dated 17/10/2018

; General preferences
G21							; Work in millimetres
G90							; Send absolute coordinates...
M83							; ...but relative extruder moves
M111 S0						; Debug off
M555 P2						; Set output to look like Marlin
M575 P1 B57600 S1			; Comms parameters for PanelDue
M667 S1						; Select CoreXY mode

; Network
M550 PMy Railcore II ZL		; Set machine name
; *** If you have more than one Duet on your network, they must all have different MAC addresses, so change the last digits
;M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0xEE 	; MAC Address
;M551 Prailcore				; Machine password (used for FTP)
M552 S1						; Enable network/wifi
M587 S"wifissid" P"password"; Configure access point. You can delete this line once connected
M586 P0 S1					; Enable HTTP
M586 P1 S0					; Disable FTP
M586 P2 S0 					; Disable Telnet

; Drives
M584 X0 Y1 Z5:6:7 E3:4:8:9 	; Map Z to drivers 5, 6, 7. Define unused drivers 3,4,8 and 9 as extruders
M569 P0 S1					; Drive 0 goes forwards (change to S0 to reverse it)| X stepper
M569 P1 S0					; Drive 1 goes backwards							| Y Stepper
M569 P2 S1					; Drive 2 goes forwards								| Extruder
M569 P3 S1					; Drive 3 goes forwards								| Extruder (unused)
M569 P4 S1					; Drive 4 goes forwards								| Extruder (unused)
M569 P5 S0					; Drive 5 goes backwards							| Front Left Z
M569 P6 S0					; Drive 6 goes backwards							| Rear Left Z
M569 P7 S0					; Drive 7 goes backwards							| Right Z

;Leadscrew locations
M671 X-10:-10:333Y22.5:277.5:150 S7.5	;Front left, Rear Left, RightS7.5 is the max correction - measure your own offsets, to the bolt for the yoke of each leadscrew

; Axis and motor configuration
M350 X16 Y16 Z16 E16 I1			; set 16x microstepping for axes & extruder, with interpolation
M92 X200 Y200 Z1600 E837		; Set steps per mm, X/Y may be more around 201.5 for accuracy
M566 X1000 Y1000 Z30 E20		; Set maximum instantaneous speed/jerk changes (mm/min)
M203 X24000 Y24000 Z900 E3600	; Set Maximum speeds (mm/min)
M201 X3000 Y3000 Z20 E1000	 	; Accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E700 I60	; Set motor currents (mA) and motor idle factor in per cent
M84 S30							; Set idle timeout

; Axis Limits
M208 X0 Y0 Z-0.2 S1				; set axis minima and low homing switch positions (adjust to make X=0 and Y=0 the edges of the bed)
M208 X290 Y290 Z280				; set axis maxima and high homing switch positions (adjust to suit your machine)

; Endstops
M574 X1 Y1 Z0 S1				; set homing switch configuration (x,y at min, z at max) IF YOU NEED TO REVERSE YOUR HOMING SWITCHES CHANGE S1 to S0

; Z-Probe
;*** If you have a switch instead of an IR probe, change P1 to P4 in the following M558 command ***
M574 X1 Z1 S2					; Set endstops controlled by probe
M558 P1 X0 Y0 Z1				; Z probe is an IR probe and is not used for homing any axes. Set Z probe type to unmodulated.
G31 X0 Y30 Z2.00 P500			; Set the Z probe trigger value offset and trigger height. (Put your own values here)
M556 S0 X0 Y0 Z0				; Set orthogonal axis compensation parameters
M557 X15:215 Y15:195 S20		; Define mesh grid
;BLTouch - leave commented out if using a IR Probe
;M558 P9 X0 Y0 Z1 H5 F50 T6000 A5 S0.02
;G31 X2 Y42 Z2.65 P25			; Customize your offsets appropriately.
;M307 H3 A-1 C-1 D-1

; Heaters and thermistors
M140 H1							    ; Remap heated bed to heater 1
M307 H1 A270.7 C90.4 D6.7 B0 S1.0   ; Kraegars Heater 1. You should set the model parameters by auto tuning (using M303) for your setup.
M305 P0 T10000 B3988 C0 R4700		; Set thermistor + ADC parameters for heater 0. Put your own H and/or L values here to set the bed thermistor ADC correction
M143 H0 S120						; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 C0 R4700 		; Set thermistor + ADC parameters for heater 1. Put your own H and/or L values here to set the first nozzle thermistor ADC correction
M143 H1 S280						; Set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H-1		 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H-1		 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off.
M106 P2 S1 I0 F500 H-1		 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off.

; Tools
M563 P0 D0 H1				; Define tool 0
G10 P0 X0 Y0 Z0				; Set tool 0 axis offsets
G10 P0 R0 S0				; Set initial tool 0 active and standby temperatures to 0C
;*** If you have a single-nozzle build, comment the next 2 lines
;M563 P1 D1 H2				; Define tool 1
;G10 P1 S0 R0 X0 Y17		; Set tool 1 operating and standby temperatures

; Automatic power saving.
; Uncomment to enable auto-pause if the power voltage drops below the pause threshold.
; The firmware records the current state of the print so that it can be resumed when power is restored
; M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" 	; Set voltage thresholds and actions to run on power loss

; Custom settings
M570 S360			; Hot end may be a little slow to heat up so allow it 180 seconds
M106 P0 S0 			; turn off fans
M106 P1 S0			; turn off fans
M106 P2 S0			; turn off fans
T0					; select first hot end

; Miscellaneous
; M501				; Uncomment if you wish to load saved parameters from non-volatile memory

Other useful places https://configurator.reprapfirmware.org/ to be able you to create your own config files https://duet3d.dozuki.com/Wiki/Tuning_the_heater_temperature_control - you will want to tune your heaters

This website uses cookies for visitor traffic analysis. By using the website, you agree with storing the cookies on your computer.More information
en/duet_reprap_300zl.txt · Last modified: 2018/10/23 14:16 by cheeseandham